Everbuild 901 Black Bitumen Paint extended informationEVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT is a solvent-based, full-bodied black bituminous paint. When dry, the product forms an odourless and taint-free black film suitable for metal protection as well as overcoating wood and felt.USESIt provides an effective waterproof, weatherproof, corrosion-resistant protective coating. It is resistant to low concentrations of alkalis and acids and can withstand prolonged oxidation. It is suitable for application to a wide variety of materials including iron, steel, lead, zinc, aluminium, asbestos-cement, concrete, stone, wood, felt and brick and is mainly used for:Metal protection – corrugated iron sheets, fire es-capes, stairways, ladders, storage tanks, gutters, downpipes, fences, railings, gates etcAs a protective coating for concrete structures, stone, brick, concrete screeds and sand/cement surfaces.Overcoating felt/wood.CHARACTERISTICS / ADVANTAGESFast drying.For use on most common building surfaces.Type of SolventWhite spiritFlashpointca. 40°CFilm Thickness Per Coat @ 11m2 / LtrWet - 0.1mm Dry -0.05mmChemical And Water ResistanceResistant to: most salt solutions, dilute acids and alkalis, water and alcohol. Not resistant to: oils, solvents and some detergent solutionsService Temps-20°C to 50°CEverbuild 901 Black Bitumen Paint product informationChemical BaseSolvent-based bitumenPackaging1L, 2.5L, 5L and 25L tinsColourBlackShelf Life24 months from date of manufacture in tightly sealed, undamaged contain- ers.Storage ConditionsEVERBUILD BLACK JACK 901 BLACK BITUMEN PAINT contains a flamable solvent, and all normal precautions against fire must be taken during both storage and use. Store in original container in cool (5°C - 25°C) dry conditions. Keep away from sources of ignition.Densityca. 0.9 g/cm3 at 20°CViscosity700-1200 cPEverbuild 901 Black Bitumen Paint technical informationService Temperature-20°C to 50°CEverbuild 901 Black Bitumen Paint application informationYieldConsumption / Yield / Dosage (PRINT single line)Porous surfaces: 4-6m2 Non-porous surfaces: 11m2Ambient Air Temperature5°C - 40°C. Surfaces must be free from ice and waterDrying time4-6 hours depending on drying conditionsEVERBUILD 901 BLACK BITUMEN PAINT SUBSTRATE PREPARATIONAs with all surface coatings, preparation of the surface is of great importance and will influence the degree of adhesion obtained and the life of the coating. All faces must be sound, stable and thoroughly clean and dry. Metal surfaces should be wire-brushed to remove rust. Where long-term protection is required an initial treatment of a rust-inhibitive product such as red lead or zinc phosphate should be used. Loose or blistered paint should be removed, as should tar-based paint systems. New galvanised surfaces should be roughened with a wire brush or treated with a etary etch primer. Porous surfaces should be primed with Black Jack Bitumen & Flashing Primer.APPLICATIONEVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT is ready for use and should not be thinned. Stir thoroughly before use. Apply by brush or spray.A minimum of two coats of EVERBUILD BLACK JACK 901 BLACK BITUMEN PAINT should be applied. The first coat should be allowed to dry (normally 2-4 hours depending on weather conditions) before the second coat is applied. Protective coating on concrete, etc: and some stone surfaces may be porous, an initial since concrete primer coat of EVERBUILD BITUMEN PRIMER should be applied.EVERBUILD 901 BLACK BITUMEN PAINT – LIMITATIONSDo not use for potable drinking water tanks.Avoid inhalation of vapours in confined spaces.Allow sufficient drying time between coats.EVERBUILD 901 BLACK BITUMEN PAINT may bleed through any paints subsequently applied over it. Apply a primer recommended by the paint manufacturer before overpainting. Categories: All Products, Building Supplies Pallet Deals
