Kerakoll Proflow Finish

Kerakoll ProFlow Finish further informationCoverage: 1.481Kg/m2 per mm thicknessAreas of applicationIntended use:Self-smoothing adjustment of irregular and uneven substrates, with rapid setting and drying, compensated shrinkage. Thicknesses from 3 to 60 mm.Compatible adhesives:single and double component organic adhesives for installing resilient floor coverings.Covering materials:LVT and design flooringvinyl, sheet vinyl and safety flooringhardwood floorstextiles, rubber, PVC, linoleum, carpetraised floorsSubstrates:mineral screeds made with Keracem Eco as binder or pre-mixed productcement-based screedscalcium sulphate-based screedsprefabricated concrete or fresh concrete castingsexisting tiled floorsflooring grade plywoodflooring grade asphalt/bitumenepoxy DPMInternal floors in domestic, commercial and industrial applications. Do not use in external applications or areas that are continually submerged.Instructions for usePreparation of substratesThe substrate must comply with current British standards and industry regulations. In general, substrates must be free of dust, oil and grease, free from any moisture rising, with no loose, flaky or imperfectly anchored parts such as residues of cement, lime, paint coatings and adhesives, which must be completely removed. The substrate must be stable, without cracks and have a functioning DPM within the subfloor. If no DPM is present, a surface epoxy DPM must be applied. Kerakoll Proflow Finish can be used to pre-smooth the floor at 95% RH prior to installing a surface epoxy DPM.In particular, substrates must be treated with a suitable primer as shown in the table:Kerakoll ProFlow Finish substratesSubstratePrimersDilution with waterCement-based screedsActive Prime FixDilutedCalcium sulphate- based screedsActive Prime FixNeatConcretesActive Prime FixDilutedCeramic floors ceramic tilesActive Prime FixNeatFlooring grade plywoodActive Prime FixDilutedGypsum fibre or fibre-cement panelsActive Prime FixDilutedMetal substratesActive Prime FixNeatEpoxy DPMActive Prime FixNeatFlooring grade asphalt/bitumenActive Prime FixNeatPreparationPour 4.5 − 5.2 l of clean water into a clean container; then pour in a bag of Kerakoll Proflow Finish, while shaking. Mix with a mechanical mixer until the mixture is smooth, lump-free and self-smoothing. Larger quantities of Proflow Finish may be prepared in suitable mixers. After the first mixing, it is advisable to leave the mixture to rest for approx. 2 minutes and then mix again briefly. Kerakoll Proflow Finish features a high degree of self-levelling capacity. Adding extra water does not improve its workability, and may cause shrinkage in the plastic phase of drying and result in less effective final performance with a reduction in surface hardness, surface finish, compressive strength and adhesion to the substrate.ApplicationKerakoll Proflow Finish is generally applied with a flooring trowel, cam rake, pin level or mechanical pump. Application with mechanical pumps allows the installer to very quickly achieve a smooth high-thickness application for large areas. The use of an aeration tool or spike roller is fine/allowed, but is not required to further improve the surface finish of Proflow Smooth, but will work to remove entrapped air from the mixture. If an additional application of Proflow Finish is required once the initial application has been completed, the first installation layer must first be hardened and ready to accept foot traffic and additional application, this is generally after 3.5 hours. The initial layer of Kerakoll Proflow Finish must be primed with a neat coat of Kerakoll Active Prime Fix prior to subsequent applications. In the case of low temperatures and high humidity it is advisable to keep the environment ventilated during application and during the hours immediately following application, in order to avoid the formation of condensation on the surface of the smoothing compound during the setting phase.CleaningResidual traces of Kerakoll Proflow Finish can be removed from tools using water before the product hardens.Special notesJoints: perimeter expansion must be allowed for in the application of self smoothing compounds. Perimeter expansion edging strip must be installed along the whole perimeter of the room, on the walls and on any other vertical elements protruding from the substrate/subfloor. All movement or expansion joints located in the substrate must be honoured.Kerakoll ProFlow Finish technical dataAppearancegrey pre-mixedApparent volumetric mass≈ 1.17 g/dm³Mineralogical nature of inert materialsilicate − crystalline carbonateGrading0-600 µmShelf life≈ 12 months from production in the original sealed packaging, protect from humidityMixing water≈ 4.5 − 5.2 l / 1 bag 20 kgSpecific weight of the mixture≈ 2.01 g/dm³ (UNI 7121)Self levelling time≈ 30 min.Temperature range for applicationfrom 5 °C to 30 °CMaximum thicknessfrom 3 to 60 mmFoot traffic≈ 90 min.Waiting time before laying:-  LVT, vinyl, sheet vinyl, safety flooring and all other resilient floor coverings≈ 3.5 hrs- resins and paints≈ 12 hrsCoverage≈ 1.481 kg/m² per mm of thicknessKerakoll ProFlow Finish performanceVOC Indoor Air Quality (IAQ) – Volatile organic compound emissionsConformityEC 1 plus GEV-EmicodeGEV certified 18293/11.01.02HIGH-TECHResistance to:- compressive after 24 h≥ 12 N/mm²EN 13892-2- compressive after 7 days≥ 21 N/mm²EN 13892-2- compressive strength after 28 days≥ 25 N/mm²EN 13892-2- flexural after 28 days≥ 7 N/mm²EN 13892-2- böhme wear after 28 days 22 cm³ / 50 cm²EN 13892-3Classification/ConformityCT–C25–F6EN 13813LimitationsProduct for professional useabide by any British standards and industry regulationsdo not use Proflow Finish to correct substrate irregularities greater than 60 mmdo not add other binders, additives or pigments to the mixturelow temperatures and high relative humidity lengthen drying times and may saturate the environment with negative consequences on the surface consistency of the smoothing compoundan excessive quantity of water will reduce product strength and increase the drying timebefore laying hardwood floors, check the residual moisture content is within the accepted parameters given by the flooring manufacturerhonour any movement or expansion joints present in the substrateif necessary, ask for the safety data sheetfor unstable wooden types, particular substrates and for any other issues, contact the Kerakoll Worldwide Global Service Categories: All Products, Floor Levelling & Smoothing Compounds Pallet Deals, Floor Levelling Compounds - Pallet Deals