Python ST Standard Set Tile Adhesive 20Kg C2TE S1 – Pallet Deals and Bulk Buy

** ATTN : PYTHON ST is now updated to the improved -> PYTHON ST MAX S1 Click here  **Python ST Standard Set Tile Adhesive C2TE S1 extended informationCoverage: 4.5kg / m2 at 3mm bed thicknessPython ST is a single part, standard setting, flexible adhesive for wall and floor tiles. It is specially formulated with extended workability, enhanced adhesion and flexibility, making it ideal for areas where slight movement or vibration can occur. Classified as S1 in accordance with EN12004 it has the high level of deformation for greater tolerance to movement. Python ST Tile Adhesive is a polymer modified adhesive which provides enhanced performance and high bond strength including installations subject to moisture. It has extended set properties for contractors who prefer a longer pot life. It is able to take light foot traffic within 18 hours of installation depending upon temperature and substrate.NB: Porous natural stone tiles need to be checked for compatibility to avoid staining.PreparationAll wall and floor substrates must be clean, dry, firm and stable, free of dust, dirt, oil and grease. Substrates should be strong enough to support the weight of the adhesive and tiles being fixed (see below for loadings).For plasterboard and plaster finishes that have been painted and are showing a weak or flaky surface finish then mechanical sanders or hand sanding blocks are generally used to remove the film. However for the likes of floor screed surface contamination, adhesive residues and weak surface laitance or even smooth dense floors such as power floated concrete, these will require a more heavy duty scarifying using specialist flooring equipment to remove the surface of the substrate to ensure the substrate is sound, stable and has a rough open texture. To encourage best adhesion to the substrate it is advisable that prior to applying adhesive that substrates are primed (please see priming section below).Remember – sanding or mechanical abrasion of any surface will leave powder deposits which require thorough removal by suitable vacuum equipment to provide a clean dust free surface. Failing to remove fine powder deposits and weak surfaces is a common reason for de-bonding of tile adhesive and primer from the substrate. Using a wet sponge to clean down a wall or floor of dust deposits only serves to spread it around, it is therefore advisable to vacuum thoroughly prior to use of wet sponge.Python ST – MIXING & APPLICATIONOnce the substrate has been prepared, continue with the tiling installation. Python ST Tile Adhesive should be added slowly to clean water in a suitable clean mixing tub and mixed thoroughly using a drill/mixer and paddle to give a slump free, easily worked mortar consistency. Once mixed the mortar is immediately ready for use and has a pot life of approximately 2 hours at 20 ̊C. Mix only sufficient material to be used within the pot life of the product. Do not remix or rewet/ dilute product which has aged and is starting to thicken or set.Mixing Ratio: 20kg unit requires 5.2L – 5.5L of water.Apply the adhesive to the required thickness (limits 3mm – 20mm) in areas up to 1m2 at a time. For internal walls use a notched trowel to the following notch dimensions to provide solid rib lines:Mosaic tiles: 3mm x 3mm at 6mm centresGeneral wall tiles: 5mm x 5mm at 10mm centresGeneral floor tiles: 8mm x 8mm at 16 mm centresFor floors and external applications we advise to use the solid bed method. This involves applying a uniform bed of adhesive to the floor and “buttering” the back of the tile with the same adhesive. When the tiles are bedded with a twisting action, pressing firmly down it ensures 100% contact is made with both the floor and the tile.When fitting tiles leave spaces between each of the tiles to allow for grouting (approx: walls 1mm – 3mm and floors 2mm – 12mm). Before the tile adhesive sets clean off the excess adhesive from the face of the tile and grout joints with a clean damp cloth or sponge.Python ST – WALL TILING & LOADINGSWall types vary considerably but all have the same basic need to be structurally sound, strong, smooth and level. It is essential that the wall to be tiled has sufficient inherent strength to hold the proposed tile and the adhesive being used. The following chart lists maximum national standard loadings for a variety of wall substrates.Leave the installed tiles for a minimum period for at least 18 hours to set hard before grouting and/or walking on the tile. This time may be extended on impervious/non-porous substrates. It is also dependent on temperatures and conditions. Always check and ensure that adhesive has set hard before grouting.WALL TILESCeramicsPorcelainGlassMosaicsMarbleTravertineGraniteLimestoneTerracottaQuarrySlateQuartzBrick slipsResin backed (** not suitable **)SUBSTRATESSand/Cement ScreedConcretePlywood Overlay (15mm min)Tile Backer BoardsCement faced fibre boardsAnhydrite/calcium sulphate/gypsum based screedsTile on Tile* (existing ceramic, porcelain and natural stone tiles (overlay) known as ‘Tile on Tile’)Firm and stable PlasterCement/Sand RenderConcrete Brick/BlockFloating FloorsHard Vinyl TilesFlooring grade asphaltGROUTINGGypsum plaster20kg/m2Skimmed plasterboard (gypsum)32kg/m2Plywood (exterior grade)30kg/m2Gypsum fibre boards40kg/m2Cement tile backer boards40kg/m2Glass reinforced cement sheets50kg/m2PRIMINGLeave the installed tiles for a minimum period for at least 18 hours to set hard before grouting and/or walking on the tile. This time may be extended on impervious/non-porous substrates. It is also dependent on temperatures and conditions. Always check and ensure that adhesive has set hard before grouting.CLEANINGTools should be thoroughly cleaned with water to remove excess material immediately after use and before adhesive sets.POINTS OF NOTEThe curing period for cement based tile adhesives will be affected by extremes in temperature. High temperature site conditions will increase the speed of cure therefore reducing the pot life and set times. Low temperatures will reduce the speed of cure extending the pot life and set times. It is therefore good practice to consider site conditions and storage of materials as essential factors in planning tiling installations.All Python adhesives are manufactured to meet the performance requirements of BS EN 12004 and the relevant classifications.Python would always advise that tiling installers follow the guidelines for tiling as laid down in BS EN5385. It is essential that expansion joints are built into the design of the tiling installation in order to prevent tension build up. This is a common occurrence which can result in tiles de-bonding.Please note that this product uses natural aggregates and other materials that may marginally vary in colour. This does not affect the consistency or characteristics of the product.Python ST Standard Set Tile Adhesive technical dataClassificationEN12004 Class C2TE S1Bed Thickness3mm – 20mmCoverage4.5kg / m2 at 3mm bed thicknessGrout After*4 hoursStorageThis product must be stored in unopened bags, clear of the ground in dry conditions. Avoid frost. Ideal storage temperatures are between 5 ̊C and 25 ̊CShelf LifeUnder the above storage conditions this product has a shelf life of 12 months.Pot Life*60 Minutes at 20°CSet Time2.5 Hours at 20°CApplication Temperatures5°C to 25°CColoursGrey and WhitePack sizes20kg bagsNoteAll work must be carried out in accordance with British Standard Code of Practice for floor and wall tiling BS5385 Categories: All Products, C2TE - Tile Adhesives Pallet Deals, S1 Tile Adhesives - Pallet Deals, Tile Adhesives - Pallet Deals